• We need your support!

    We are currently struggling to cover the operational costs of Xtremepapers, as a result we might have to shut this website down. Please donate if we have helped you and help make a difference in other students' lives!
    Click here to Donate Now (View Announcement)

chemistry and physics P5 tips

Messages
16
Reaction score
8
Points
13
If there is anyone out there w ho has some good tips or notes how to solve p5 chemistry ( most importantly)
and physics notes or tips please help me with that . Your effort will be appreciated .
Thank you
May Allah help us succeed in our exams
 
Messages
57
Reaction score
90
Points
28
For planning section:
1. When asked to draw a diagram, ALWAYS mention the volume of the apparatus being used. The one most often used is gas syringe. I think it is better to limit the volume of syringe to less than 500 cm3 . Also, the volume of a commonly used small test tube is around 16 cm3 and that of a boiling tube is about 25 cm3. We always have to keep the volume of the apparatus we are using while choosing the volume of the solution for the planning. Saying that we are going to place 50cm3 of aqueous HCl in a test tube is of course not going to please the examiners. I think I ended up doing the same in one of the papers where we had to prepare different concentrations of a given solution. I chose volume of water to be added to a beaker to be 250 cm3. However, the ER stated that the volume should be less than 200cm3, that so being since the volume of a commonly used glass beaker is around 250cm3. Someone carrying out my expm would have a fully filled beaker. However, we can use greater volume if we state that the volume of the beaker is 400cm3 or 500 cm3 or so on. So, stating the volume of the apparatus is very very important
2. Always while measuring volume of solutions, use burette or pipette because they have low PERCENTAGE error. The question of percentage errors are usually asked in P5. The percentage error becomes very unacceptable if we are measuring SMALL volumes of solution or small masses. So, a 3dp balance is much better for measuring masses than a 2dp balance as it would have much less % error when small masses are being measured
3. While heating crystals strongly, do not use a simple test tube or any apparatus with sharp edges as they are liable to crack at the sharp edges. For very strong heating to a constant mass, a crucible placed on a pipe clay triangle is appropriate. And of course to measure the mass of the crucible + solid, you would have to place it on a balance. But we wouldn’t want to fry our poor balance by placing a very hot crucible on top of it. So, allow the crucible to cool for a few minutes by placing it on a heat mat.
When using a magnesium ribbon or any dirty surface, clean it with SANDPAPER
How to prepare crystals (which is also linked with solubility)
Many methods are mentioned in MS but I found this to be the simplest:
CIE usually demands us to prepare crystal after preparing a saturated solution of the crystal.
So, we have to prepare a saturated solution first:
1. Take a fixed volume of water in a beaker of appropriate volume
2. Add the crystal to the water and stir continuously. You have to allow some time for the crystal to dissolve as it is an equilibrium process
3. After 5 min of stirring , if no solid crystals appear, add further mass of crystal
4. And repeat the process until solid appears in the beaker
5. Filter the solution using a filter paper and funnel so that the saturated solution is collected in a beaker(whose mass has been measured previously) beneath the funnel
Now we have a saturated solution in a beaker.
How to get the crystals:
1. We have to place the beaker in a warm water bath. We could use a burner as well but there is a risk of overheating the solution which could decompose the crystal. If the heat is appropriate, the water of the solution should evaporate and we should have dry crystals ready.
How to measure solubility:
6. Measure the mass of beaker + solution from step 5
7. Subtract the mass of beaker from the mass in 6 to get the mass of saturated solution
8. And evaporate as shown above to get the mass of crystals.
8. Measure the mass of crystal + beaker
9. Subtract mass of beaker from mass in 8 to get the mass of crystals
10. Subtract the mass of crystals from the mass of saturated solution to get the mass of water in the solution
11. I have assumed that all the masses are in grams. So, to get the solubility: Mass of crystal x 100/Mass of water
When you have to remove moisture from :
1. Surface:
Wash the surface with a stream of propanone. The water gets dissolved in the propanone and repeat it multiple times. Then gently heat the surface to evaporate the propanone from the surface
2. Vapour:
Use dessicants such as:
1. ANHYDROUS sulphuric acid
2. ANHYDROUS calcium chloride
3. Silica gel
You have to pass the vapour from the beaker containing the dessicant
Also, a useful property of soda lime is that it absorbs BOTH water vapour and carbon dioxide
We are also regularly asked to measure enthalpy changes
Most of us already know that we use a plastic cup and thermometer for this purpose
However this has many disadvantages (asked regularly) and here are some of them with the required measures:
1. Heat loss to the surroundings from the beaker:
To avoid this:
a. Cover the plastic cup with a lid
b. Place the cup in a beaker. The air in the beaker acts a good insulator.
c. Use multiple cups so as to thicken the lateral layer of plastic
2. Instability of the cup
a. Place the cup in a glass beaker
3. For exothermic reactions, spray of the solution very likely
a. Use a large beaker to carry out the experiment rather than the small plastic cup (which has a small volume)
b. Put a lid on the top of the beaker (this only MINIMISES the spray, doesn’t prevent it totally)
4. When we are heating a volume of water in glass beaker, there are two cases of heat loss to consider:
a. Heat loss from the beaker of water
b. Heat loss from the burner heating the volume of water
When preparing a solution of a fixed concentration from a given parent solution of concentration , say, 2.0 mol/dm3
A. We are required to prepare a solution of concentration of 1.0 mol/dm3 with volume 250 cm3 ( the concn cannot be greater than 2 !!!!!!!!!!!!!!)
a. Add 100 cm3 of the parent solution to a volumetric flask of marking at 250 cm3
b. Top off with water to the mark of 250 cm3. Use a wash bottle for this purpose to have greater control over the addition process
When required to prepare 250 cm3 of 0.5 mol/dm3 solution of a crystal of Mr 50g
First realize that we need only 250 cm3, not 1 dm3
Now in 250 cm3 there will be: 50/4 = 12.5 g of the solid
So, first add 12.5 g of solid to 50 cm3 of water in a BEAKER ( not the volumetric flask yet). Also note that the volume of water is less than 250 cm3.
Stir properly and if the solid doesn’t dissolve add more water until it fully dissolves
Then transfer the solution from the beaker to a volumetric flask. Remember to rinse the beaker with water and transfer the solution to the volumetric flask
Stopper the flask and shake properly
Finally, add the required volume of water to make the solution upto 250 cm3 USE A FUNNEL OR YOU RISK OVERSHOOTING THE MARK
Titration is accurate because:
1. Standard solution of acid/base is used
2. we obtain concordant titres
3. % error in pipette and burette is very small
4. The end point of a titration is sharp

There is more at: http://studyguide.pk/?p=1727#ixzz2wx6gvZ6V
 
Top